How to Price Ductwork and HVAC Jobs (With a Worked Example)
Updated by the EstimateDynamo team
To price a ductwork job, measure each duct run, price the duct, fittings and sealing materials, estimate labor from the access conditions, then add overhead and your target profit. The same method works for most HVAC service jobs. This guide shows each step and ends with a worked example you can copy.
Step 1: Measure and sketch the system
Walk the system and sketch every run. Record the length of each trunk and branch, the duct size, the number of elbows, tees and transitions, and how many registers, grilles and returns are involved.
Note where the ducts run. Attic, crawlspace, basement and wall cavity work all take different amounts of time, and tight access is where hours disappear.
Step 2: List every material
- Duct by type and size: flex, rigid sheet metal, fiberglass duct board or round pipe
- Fittings: elbows, tees, reducers, collars and boots
- Insulation or insulated duct where code requires it
- Mastic, foil tape, straps and hangers
- Registers, grilles and dampers
- Fasteners and sealing materials
Step 3: Estimate labor from the conditions
Labor is the biggest swing factor. Estimate hours per run from your own history, then adjust for access: attic heat, crawlspace height, finished ceilings, and how much existing duct has to come out first.
Include demolition and removal of old duct, cleanup, and any time spent moving stored items out of the way.
Step 4: Add the costs people forget
- Permit and inspection fees
- Duct leakage testing or system balancing when required
- Disposal of old duct
- Travel, parking and material pickup
- Warranty callbacks on tight or difficult work
Step 5: Add overhead and profit
Add your overhead rate first, then apply the margin you need. Remember that markup and margin are different numbers: a 25% markup gives only a 20% margin. Use the markup and margin calculator to check the price before you send it.
Worked example: replace 60 feet of flex duct and 4 boots
Illustrative figures only. Replace every number with your own current rates and local costs.
| Line | Basis | Amount |
|---|---|---|
| Labor | 10 hrs x $85 | $850.00 |
| Insulated flex duct | 60 ft x $6 | $360.00 |
| Fittings, boots and collars | Allowance | $220.00 |
| Mastic, tape and straps | Allowance | $90.00 |
| Disposal and travel | Allowance | $75.00 |
| Subtotal (your cost) | $1,595.00 | |
| Markup 25% (20% margin) | $398.75 | |
| Price to customer | $1,993.75 |
Pricing other HVAC jobs with the same method
Equipment replacement, repairs and maintenance plans all follow the same pattern: list labor, equipment and materials, add fees and overhead, then apply profit. For a full system install, read the guide on pricing an HVAC installation, then build the estimate in the free HVAC estimate calculator.
Common ductwork pricing mistakes
- Pricing by linear foot without checking access
- Forgetting to price removal and disposal of the old duct
- Leaving out testing, balancing or permit costs
- Using a flat rate that ignores attic or crawlspace conditions
- Not putting exclusions in writing, such as drywall repair or insulation upgrades
Put it into practice
Use your own rates, see live totals and download a professional PDF. No account needed.
Open the HVAC estimate calculatorFrequently asked questions
How do you price ductwork?
Measure each run, price the duct and fittings, estimate labor from the access conditions, add permits, disposal and travel, then add overhead and profit. Many contractors compare the result against a price per linear foot as a sanity check.
Should I price ductwork per foot or by the job?
Per-foot pricing is a quick benchmark, but a job price built from labor and materials is safer because access, fittings and removal change the real cost from house to house.
What should be excluded from a ductwork estimate?
Common exclusions are drywall or ceiling repair, insulation upgrades, electrical work, asbestos or mold remediation and changes to the system design.
How much markup should I add to HVAC work?
It depends on your overhead and market. Work out your own overhead rate, decide the margin you need, and use a markup that delivers it. A 25% markup equals a 20% margin.
How do I price a general HVAC job?
List labor hours, equipment and materials, then add permits, disposal and travel, overhead and profit. The same steps work for repairs, replacements and installs.