EstimateDynamo

Markup vs Margin for Contractors: Calculator, Formulas & Examples

Updated by the EstimateDynamo team

Markup is the percentage added to cost. Margin measures the amount above cost as a percentage of the selling price. A 25% markup gives a 20% margin, not 25%. Whether that amount is gross profit, contribution or net profit depends on which costs you included. Use the calculator below to compare the two before pricing a job.

Markup and margin calculator

Enter your total job cost and the percentage you want. It shows the price to charge and the matching markup and margin.

Price to charge
$13,333.33
Amount above cost
$3,333.33
Markup
33.3%
Margin
25%

Amounts are before tax. Costs not included here still reduce your eventual profit.

The short answer

Markup is calculated on cost. Margin is calculated on price. For a positive markup, the margin percentage is smaller than the markup percentage. At zero markup, both are zero.

If you need to hit a target profit, work from margin: divide your cost by (1 minus your target margin) to get the price.

The four formulas

  • Markup % = ((price - cost) / cost) x 100
  • Margin % = ((price - cost) / price) x 100
  • Price from markup = cost x (1 + markup % / 100)
  • Price from target margin = cost / (1 - margin % / 100)

A worked example

Say a job costs you $10,000 in labor, materials and overhead. With a 25% markup the price is $12,500, so your profit is $2,500, which is a 20% margin, not 25%.

For a 25% margin, the price is $10,000 / 0.75 = $13,333.33, rounded to cents. The amount above included cost is $3,333.33. The required markup is 33.333...%; rounding it to 33.3% before calculation gives a slightly different price.

A complete cost worksheet

These are invented amounts, not recommended rates. Include equipment, permits, disposal and other job costs where applicable. The $3,333.33 is only a net-profit estimate if every relevant cost is included; otherwise it must still cover the costs you left out. Sales tax and customer deposits are not profit.

Included costAmount
Loaded labor$6,000.00
Materials and delivery$3,000.00
Allocated overhead$1,000.00
Total included cost$10,000.00
Price at 25% margin, before tax$13,333.33
Amount above included cost$3,333.33

What a discount does to margin

On the $10,000 cost example, a 10% discount reduces the $13,333.33 price to $12,000.00 after rounding. The amount above cost falls to $2,000.00 and margin falls to 16.67%, not 25%. Recalculate against the final selling price whenever you discount a job.

Markup to margin conversion table

Use this table to convert between the two. Find the margin you want and apply the matching markup to your cost.

Markup and margin equivalents
Target marginMarkup neededPrice on a $1,000 costProfit
10%11.1%$1,111$111
15%17.6%$1,176$176
20%25.0%$1,250$250
25%33.3%$1,333$333
30%42.9%$1,429$429
35%53.8%$1,538$538
40%66.7%$1,667$667
50%100.0%$2,000$1,000

Include overhead before you add profit

Overhead is the cost of running the business: insurance, vehicles, software, office, licensing, advertising and unbilled time. If it is not in your price, it comes out of your profit.

One allocation method divides annual overhead by annual direct job costs. If overhead is $60,000 and direct costs are $300,000, that allocation is 20% of direct cost. Check that the method suits your workload and update it against actual results. Do not add the same overhead again if your loaded labor or other rates already include it.

Common mistakes

  • Adding a markup percentage and reading it as profit margin
  • Applying markup to materials only and forgetting labor and overhead
  • Copying a competitor's percentage without knowing your own overhead
  • Giving a discount without checking what it does to margin: a 10% discount on a 20% margin job can cut profit in half
  • Leaving out warranty callbacks, waste and unbillable travel time

Markup on materials vs labor

Many contractors mark up materials and bill labor at a loaded hourly rate that already contains overhead and profit. Either approach works as long as the total job covers direct cost, overhead and your target profit.

What does not work is guessing. Check the final price against the cost, then read the margin before you send the estimate.

How to use this in an estimate

Enter your true costs line by line, apply a markup that delivers your target margin, then review the profit figure before you send. Seeing cost, price and profit side by side makes underpriced jobs obvious before you commit to them. The free estimate generator does this live as you type.

Put it into practice

Use your own rates, see live totals and download a professional PDF. No account needed.

Try the estimate calculator

Frequently asked questions

What is the difference between markup and margin?

Markup is profit divided by cost. Margin is profit divided by selling price. A 25% markup equals a 20% margin, and a 50% markup equals a 33.3% margin.

How do I convert markup to margin?

Margin = markup / (1 + markup). For example, a 40% markup gives 0.40 / 1.40 = 28.6% margin. To go the other way, markup = margin / (1 - margin).

What markup should a contractor use?

Use your actual job costs, overhead, capacity and desired return to choose a target. There is no universal percentage that makes every contractor profitable. Convert that target margin to markup, then compare estimated and actual costs after each job.

Is markup calculated on cost or on price?

Markup is calculated on cost. Margin is calculated on the selling price.

How do I get a 30% profit margin?

Divide the included cost by 0.70. A $10,000 cost becomes a $14,285.71 price, rounded to cents. That requires approximately 42.86% markup, not 30%. Any omitted costs still reduce your eventual profit.

Keep reading